See Our Work
Repair work from our forklift, truck, and specialty equipment teams. Open a job for the problem, repair details, and photos.

Nissan MCP
The forklift overheated with a leaking water pump and a thermostat stuck shut.
View repair details
Toyota 7FGCU
A custom brake line restored braking and returned the forklift to work.
View repair details
Hoist F400
No-start diagnosis and repair.
View repair details
Mitsubishi FBC15N
A custom feed hose stopped a hydraulic leak.
View repair details
Case 580 Super L
Timing cover plug and hydraulic hose repairs fixed two separate problems.
View repair details
Clamp forklift
Loose hydraulic hoses caught in the overmast pulleys.
View repair details
UTILEV UT25P
Radiator and cooling components replaced and tested.
View repair details
Komatsu FG30HT-16
Worn rollers let the carriage move out of position in the mast.
View repair details
Loading dock
Broken and missing pins left the dock plate out of alignment.
View repair details
Doosan GC55C-9
Damaged flywheel teeth required transmission removal.
View repair details
Toyota 7FGCU
The lift lost braking. Both wheel cylinders seeped and the master cylinder bypassed fluid.
View repair details
Toyota
TCS replaced a failed transmission on site in one day.
View repair details
Freightliner M2 112
A split airbag and leaking axle airlines were repaired the same night.
View repair details
CAT DP40N
A blown cooler hose drained transmission fluid and stopped travel.
View repair details
International HV607
Damaged support beams, deteriorating air bags and leaking shocks needed attention.
View repair details
Crown PE4500
Gear oil leaked from the lower drive unit in cold storage.
View repair details
Taylor GT-300
Broken hoses and bent mounting brackets prevented normal lift operation.
View repair details
UniCarriers MAP1F
A PM inspection identified wear throughout the rear steering assembly.
View repair details
Fontaine
A 2015 trailer needed hub service, replacement deck boards and a marker light before inspection.
View repair details
Peterbilt 340
A snapped belt brought on the battery light and stranded the truck.
View repair details
Mack CHU
Failed injector cups caused extended cranking on this 2009 Mack.
View repair details
Raymond SA Swing Reach
Intermittent B-0 and B-1 faults shut the truck down in an aisle.
View repair details
Ford F-150 XLT
Front brake service exposed a collapsed hose and seized caliper slide pin.
View repair details
Ford F-450 Super Duty
A smoking battery had low electrolyte and a dead cell.
View repair details
Bobcat S250
Hydraulic oil leaked from a hardened vent-cap O-ring and a bucket tilt hose that had chafed under its sleeve.
View repair details
Yale GLP040
Hydraulic fluid pooled under the forklift from failed clamp cylinder seals.
View repair details
Freightliner 114SD
During service on this 2018 truck, we found the oil pan gasket and injector pass-through seals needed replacement.
View repair details
International MAO 25
Worn oil cooler seals allowed coolant to escape on this 2016 International.
View repair details
Bobcat G30E
Intermittent hydraulic shutdowns traced to a cracked seat switch and a failing OSS module that dropped the five-volt sensor supply when warm.
View repair details
Mack MD7
A coolant leak on this 2023 MD7 appeared only under pressure at operating temperature.
View repair details
Freightliner M2
Fork contact during loading damaged the wiring for the truck-mounted forklift.
View repair details
Hyster H80XM
Worn flywheel teeth required engine removal.
View repair details
Terex SS842
The main boom cylinder was leaking hydraulic fluid.
View repair details
John Deere 624J
The cooling fan pulled in the rear lighting harness and blew fuses.
View repair details
Kenworth T880
A blocked check valve kept the tag axle in the down position.
View repair details
Taylor GT300
Failed seals allowed both fork positioner cylinders to leak.
View repair details
CAT 2PD6000
A PM inspection caught loose steering parts and a hydraulic tank leak.
View repair details
CAT DP50K
An internally leaking steering orbital left the forklift without rear steering.
View repair details
Yale GLC080VX
An operator found the clamp loose on the carriage during a pre-shift check.
View repair details
Kenworth T880
A broken pipe caused a complete loss of secondary air pressure on the road.
View repair details
Tractor with front-end loader
The steering cylinder broke away from the axle. The hydraulic lines kinked, the tie rods were worn and the tractor leaked fluid.
View repair details
Freightliner 114SD
Four deteriorated suspension air bags were leaking.
View repair details
Crown PE 4000
The truck was difficult to steer and its horn was silent.
View repair details
Freightliner Cascadia
A failed trailer cord was replaced and the lights were tested.
View repair details
Crown RM 6000
Lift height faults appeared intermittently as the carriage moved.
View repair details
Lull 844-C42
Corrosion made the brake pedal stiff during operation.
View repair details
Komatsu FG25ST
A no-start call led to a battery reading of just 3.5 volts.
View repair details
Komatsu FG25ST
A failed water pump and cracked radiator caused coolant loss and overheating.
View repair details
CAT DP40
The engine ran, but travel and other functions were disabled.
View repair details
International LT625
Active engine faults pointed to a failed variable geometry turbo actuator.
View repair details
2015 Freightliner M2
New batteries and ECM recalibration resolved a no-start.
View repair details
Yale GLP060
The forklift overheated with a failed water pump and thermostat stuck closed.
View repair details
Doosan GC55C-9
A broken tilt cylinder mounting ear put the forklift out of service.
View repair details
Caterpillar NRR40
The mast cable twisted off its roller after a tension spring came loose.
View repair details
International HV607
An internal compressor failure seized the clutch and stopped the A/C from cooling.
View repair details
Hyster S120
Fluid was bypassing the long-arm cylinder seals and leaking from the clamp.
View repair details
Taylor GT 300
Excessive blowby and low compression traced to piston and ring failure.
View repair details
Moffett M8 55.4
Worn bearings and pads let the carriage grind against the mast.
View repair details
Toyota 7FGCU35
A cracked, dry-rotted belt snapped and stopped the lift.
View repair details
Sumitomo SC500
The operator heard crunching as the boom moved, and the cable showed broken strands.
View repair details
Case 580M
A seized compressor threw the belt and the cab lost cooling.
View repair details
Isuzu NRR
An inspection identified worn brakes on both axles.
View repair details
JCB 436
A leaking lift pump was replaced during follow-up service.
View repair details
Bobcat G30E-7
A slipping gear stopped the wiper from sweeping the windshield.
View repair details
Ford/New Holland 555E
Inspection found leaking boom and dipper cylinders, cracked hoses and worn brake components.
View repair details
Komatsu PC400LC
The excavator had no power and a melted battery cutoff solenoid.
View repair details
Hyundai 30L-7A
An impact broke a hydraulic pipe away from its mounting block.
View repair details
Yale GLC080VX
A puddle beneath the lift led to a cracked cylinder weld that leaked under pressure.
View repair details
Hyster S120
Broken middle and lower bearings left the carriage hanging on the rollers.
View repair details
Case 580 Super M
Both stabilizers leaked, one at the cap and one at the scraper seal.
View repair details
Caterpillar DP50N1
A nick on the rod caused the lift spool to jam and the control lever to stick.
View repair details
Nissan MCP1
The lift was low on power with a failed coil pack and an incorrect oxygen sensor reading.
View repair details
Crown PE4500
A gearbox teardown revealed loose housing bolts, missing shims and a pinched gasket.
View repair details
Hyundai 50-7A
A maintenance inspection revealed leaks at the mast and engine.
View repair details
JLG 400A
Hydraulic oil was escaping from the boom cylinder and fittings beneath the turret.
View repair details
Toyota 8FGCU
A rust-filled radiator and stuck thermostat caused overheating severe enough to burst the lower hose.
View repair details
2018 Freightliner M2
A cracked ignition fuse caused an intermittent shutdown.
View repair details
Caterpillar DP50CN1
The mast rose too early while the free lift cylinder leaked and the carriage stuck.
View repair details
Mack CXU
The truck had active EGR cooler efficiency and oil thermostat faults.
View repair details
Freightliner 114SD
An A/C clutch fault led to a failed clutch and a crushed low-pressure line.
View repair details
Toyota 8FGCU
A failed converter seal allowed transmission fluid to leak.
View repair details
Case IH 580N
Warning lights came on and the backhoe would not release the park brake.
View repair details
Hyster S100FT
An empty propane tank and a battery at 5.42 volts left the forklift unable to start.
View repair details
Takeuchi TL130
Dirt packed around the drive motor connections made the worn hoses difficult to access.
View repair details
Toyota 8FGCU
The engine surged at idle with a plugged regulator and clogged idle injector.
View repair details
Moffett M8 55.4
An impact beneath the forklift bent a hydraulic solenoid and damaged its seal.
View repair details
International 4300
The inspection uncovered worn rear brakes, a bypassing brake chamber and play in the carrier bearing.
View repair details
Mack CXU
Engine oil was leaking around the oil filter housing.
View repair details
Freightliner M2 112
The truck lost air while parked, and all four air bags showed deep cracks and dry rot.
View repair details
Yale GLP030
The engine overheated because the water pump had failed and the thermostat was stuck shut.
View repair details
Doosan D70S-5
A leaking tilt cylinder needed replacement, and its mounting pins had seized.
View repair details
Toyota 8FGCU
Severely worn clutch packs caused slipping and kept the forklift from going into gear.
View repair details
Ford F-650
A check engine light led to an active soot sensor heater fault.
View repair details
Doosan GC55C
The steering axle had fallen out for the third time.
View repair details
Toyota 8FGC55U
Operating the clamp revealed a cracked long-arm cylinder leaking hydraulic fluid.
View repair details
Pratt Industries
The trailer had weak, squealing brakes. Inspection found worn shoes and heat cracks in the drums.
View repair details
Hyster 120
Several hydraulic lines had split open and were leaking.
View repair details
Mack CXU
The engine stayed below operating temperature and cab heat came and went.
View repair details
Toyota 8FGCU
A rough-running engine had a misfire and restricted LPG flow.
View repair details
International LT625
An injection rail pressure fault led to a fuel separator packed with debris.
View repair details
PiggyBack PB 55.4
The tilt cylinders leaked and the engine air filter was heavily soiled.
View repair details
New Holland B95C
The batteries read 12.6 volts at rest but dropped to 2 volts during cranking.
View repair details
International HV607
Several rear lights failed and the left front hub cap leaked gear oil.
View repair details
Sierra RB6000
The engine lost power under load and logged a cylinder four injector fault.
View repair details
Wiggins W2.0M3-104H3-31/10
Inspection found multiple external leaks and a main lift cylinder bypassing internally.
View repair details
Peterbilt 340
Three cracked rear air bags were leaking and the truck was losing air.
View repair details
UniCarriers MCP1
The forklift would not start, and the starter motor was shorting internally.
View repair details
Hyster 120XMS-PRS
A pinched hose pulled a fitting out of the control block and damaged its threads.
View repair details
Transcraft Steel Flatbed
Contact with a highway barrier damaged the trailer brakes and air suspension.
View repair details
Doosan G25P-5
Operating the attachment sent hydraulic fluid spraying from a positioner cylinder.
View repair details
Crown WP3000
Fault 329 restricted travel speed because the steer motor temperature signal was out of range.
View repair details
Isuzu NPR
The rear door stuck in its tracks and sometimes would not open.
View repair details
Genie GTH-1544
A fuel line rubbed against a shield until a pinhole formed beneath the engine.
View repair details
CAT GC45K
The pedal felt hard and the forklift had no braking ability.
View repair details
International MV607
The brakes squealed and locked up. Inspection found thin pads and warped rotors.
View repair details
Great Dane
The liftgate had weak electrical power and its hydraulic pump was leaking.
View repair details
Mitsubishi FG30N
Brake pressure dropped while the operator held the pedal down.
View repair details
Wiggins
The cylinder eyelets were heavily worn where the fork positioner attached to the carriage.
View repair details
Case IH 580
The starter had failed, and inspection also revealed a cracked A/C belt.
View repair details
Yale
Failed seals allowed hydraulic fluid to leak from the Cascade clamp cylinders.
View repair details
CAT GC45K SWB
Cycling the forklift exposed a hydraulic hose that had rubbed through.
View repair details
Mack CXU
Coolant was leaking beneath the engine at the aftertreatment lines.
View repair details
Pack Mule SC-775-4NXG
The vehicle shut down intermittently while operating.
View repair details
UniCarriers MCP1F1A14LV
The front and rear tires were worn out.
View repair details
Freightliner M2
The liftgate pump would not run in either direction during a delivery.
View repair details
International MA025
An erratic oil pressure reading pegged at maximum. The sensor connector had broken wires and oil intrusion.
View repair details
International
Worn compressor lines were leaking coolant on a 2019 truck.
View repair details
Yale GLC040AFNUAE083
The free lift cylinder leaked and bypassed internally. The steer cylinder was also leaking into the steer beam.
View repair details
Crown WP3000
The pallet truck lacked power and could not lift properly.
View repair details
Isuzu FTR
The truck body had a damaged roof section and corner cap.
View repair details
Hyster S120FT-PRS
The clamp would not hold pressure because fluid was bypassing worn cylinder seals.
View repair details
Truck
The damaged toolbox would no longer stay secured to the vehicle.
View repair details
Hyster S120
A failed water pump bearing let the fan contact the pulley, damaging the fan and causing overheating.
View repair details
Freightliner Cascadia
The power steering reservoir and lines had deteriorated and were leaking.
View repair details
Freightliner Cascadia
The lights and ignition cut out intermittently on the 2011 truck.
View repair details
Hyundai 40L-9
Brake pressure dropped because fluid was bypassing inside the master cylinder.
View repair details
Ford F-550 Super Duty XL
An intermittent turbocharger failure kept triggering the check engine light.
View repair details
Toyota 8FGCU
A loud clunk when shifting into gear came from excessive transmission movement.
View repair details
Mack CXU
The 2012 truck would not crank. One battery measured 7.4 volts and the starter failed despite a good trigger signal.
View repair details
International MV607
A failed outer hub cap let the rear hub lose its oil.
View repair details
Broken steering pivot
A snapped steering linkage left the unit without steering.
View repair details
Hyster 120
A worn outer seal allowed fluid to leak from the planetary hub.
View repair details
International LT625
A corroded strap failed and left the exhaust hanging beneath the truck.
View repair details
UniCarriers MCP1
A deteriorated gasket slipped out of position and allowed hydraulic oil to leak.
View repair details
International HV607
A failed tensioner threw the serpentine belt out of alignment and shredded it.
View repair details
Link-Belt 218 HSL
The crane needed a complete wire rope replacement.
View repair details
Trail King
Impact damage left the landing gear unusable.
View repair details
Ford E350
Air came out only through the defroster vents, regardless of the driver's setting.
View repair details
Wiggins W220M2-34/12
Both main lift cylinders leaked enough hydraulic oil to leave puddles under the mast.
View repair details
Kohler
The engine shut down seconds after starting. A shredded belt stopped coolant circulation and charging.
View repair details
Forklift slip sheet attachment
A failed cylinder seal let hydraulic oil escape from the sideshift attachment.
View repair details
Forklift
An impact snapped the left steer knuckle and left a rear wheel unable to turn.
View repair details
Hyundai 30L-7A
The engine surged, stalled and intermittently lost throttle response.
View repair details
UniCarriers MJ1F4A35LV
The operator reported a loose front wheel and poor braking. Inspection found loose lug nuts, broken studs and a broken left brake drum.
View repair details
Yale GLP60
A no-start left the customer unable to unload a delivery. The battery measured just 10 volts at rest.
View repair details
International HV607
Active particulate filter faults and excessive soot accumulation put the truck into a derate.
View repair details
Toyota 6FGCU-30
Overheating damaged the cylinder head and caused the head gasket to fail.
View repair details
Doosan GC25S
Packing banding wrapped around the pinion seal and damaged both the seal and yoke.
View repair details
International HV607
The Moffett lights stopped working because the angled socket mount forced the cable against the stabilizer housing.
View repair details
Toyota 8FGCU
Hydraulic oil escaped from a crack around the cylinder weld.
View repair details
Nissan MCP1
The free lift bolts had pulled out of the cylinder and the truck could not recognize that the parking brake was engaged.
View repair details
Freightliner Cascadia
The truck could not regenerate after a compressor failure contaminated the DEF air system with oil.
View repair details
Hyster Paper Roll 120
Starter wiring and disconnected components were repaired after a fire.
View repair details
New Holland LX665
A major engine oil leak required access beneath the engine.
View repair details
Toyota 8FGCU
Failed steering components required replacement of the steer beam assembly.
View repair details
Freightliner Cascadia
The fifth wheel would not lock onto the trailer kingpin.
View repair details
Truck-mounted forklift
A hydraulic hose burst while the forklift was still mounted on its carrier.
View repair details
UniCarriers MCP1F1A15LV
A failed starter kept the forklift from starting.
View repair details
Hyster 80
The mast would not hold its tilt position.
View repair details
Hyundai
Internal bypass in the master cylinder reduced braking pressure.
View repair details
Toyota 8FGCU
Wear in the carriage allowed the fork pins to slip out of place.
View repair details
Crown
Hydraulic fluid was pouring from beneath the battery compartment.
View repair details
Moffett M8 55.4
A puddle beneath the lift led to several valve O-rings pushing out of the control block.
View repair details
Isuzu NQR Base
A failed compressor left the cab without air conditioning.
View repair details
Leaking steer cylinder
A steer cylinder was losing hydraulic oil through failed seals.
View repair details
Hyster S155XL2
The truck had lost braking, and inspection revealed both an inoperative master booster assembly and leaking main lift cylinders.
View repair details
CAT GC45K
An internal starter failure prevented the starter from engaging the flywheel.
View repair details
Case 580L
The main boom cylinder had a major hydraulic leak and its gland nut was seized.
View repair details
Pratt
A leaking forward hub left gear oil around the wheel end and ABS components.
View repair details
Forklift
A broken directional switch in the steering column had been improvised to keep the lift running until the control failed.
View repair details
CAT GC45K
Dragging wore down the attachment tips, and the right pin was seized and welded in place.
View repair details
Terex SS842
A wheel hub was leaking oil.
View repair details
Hyster 120
A broken cooling fan and damaged radiator left the forklift out of service.
View repair details
Utility
Two fittings snapped off in the distribution block, leaving the trailer unable to hold air pressure.
View repair details
Freightliner 114SD
Tail, brake and turn lights cut out intermittently where the harness rubbed the Moffett fork mounts.
View repair details
New Holland
A running check showed oil escaping at the filter seal and from a hydraulic hose.
View repair details
Freightliner 114SD Base
Three swollen batteries were leaking and venting gas on the 2018 truck.
View repair details
Hyster 120
A snapped mounting pin was lodged in the cylinder and left it sitting crooked.
View repair details
CAT DP40KL-D2
Both staging cylinders were leaking hydraulic fluid.
View repair details
Freightliner Business Class M2
Brake service uncovered seized anchor pins and bushings.
View repair details
Moffett M8 55.4
The lift was losing hydraulic fluid at a control valve fitting.
View repair details
Hyster clamp forklift
The lift would not start and its clamp was stuck in place.
View repair details
Komatsu FG25ST
A loud squeal led to deteriorated steer wheel bearings.
View repair details
Hyster S120FT
Brake failure left the forklift out of service.
View repair details
Hyster S120FTPRS
The engine ran rough and repeatedly backfired.
View repair details
Yale GLP030
Failing tilt cylinder seals allowed hydraulic oil to escape.
View repair details
Chevrolet Express 3500
The van was running hot with a failing water pump.
View repair details
Caterpillar GP40KL
A failed flywheel left the forklift unable to start.
View repair details
Volvo VHD
A maintenance inspection caught oil leaking from the rear timing cover of the D13 engine.
View repair details
Kohler
The generator fitted to a Freightliner M2 106 was sidelined by a fuel leak.
View repair details
Yale GLP050
Severely damaged cylinder head threads allowed the spark plugs to blow out.
View repair details
Isuzu NPR
A brittle oil line split and left oil on the engine and frame.
View repair details
JLG 400S
The boom lift would not start and the auxiliary motor ran continuously whenever the battery was connected.
View repair details
International 4300
Gear oil was leaking from the drive axle seal.
View repair details
Komatsu forklift
A fluid leak after overheating led to a failed radiator.
View repair details
Isuzu FTR
Oil was leaking from the output shaft seal on the Allison 3000 Series transmission.
View repair details
Box truck
A forklift impact broke through the lower bulkhead of the cargo box.
View repair details
International HV607NE
Smoke from the rear tandems led to failed wheel seals and oil-contaminated brakes.
View repair details
Hydraulic oil pooling under unit
A loose solenoid damaged its O-rings and left hydraulic fluid pooling under the unit.
View repair details
PD6000 forklift
An on-site sideshift hose repair returned the lift to service.
View repair details
Toyota 8FD70U
Both leaking staging cylinders were resealed and tested.
View repair details
2022 Freightliner M2 106
A chafed harness caused intermittent turn-signal fuse failures.
View repair details
Backhoe loader
The boom hose tore when the backhoe struck a garage door coming out of storage.
View repair details
Nissan MCPL02A25LV
Excess carriage movement broke the sideshift cylinder bracket.
View repair details
Raymond 750-DR32TT
Severely damaged load wheels caused loud noise and rough travel.
View repair details
Moffett
Worn carriage rollers caused poor alignment, unstable movement and play in the mast.
View repair details
International
The truck had no turn signals and there was no power at the light socket.
View repair details
Mitsubishi FG30N
Teardown showed heat-glazed brake shoes and excessive brake misadjustment.
View repair details
Tennant T15
The scrubber did not dispense water properly, and its brush head would not raise or lower.
View repair details
Forklift
A fork punctured the radiator of the low-mast forklift needed for an upcoming job.
View repair details
Wiggins W200
The mast drifted and both tilt cylinders were leaking.
View repair details
Freightliner M2
The truck had no air conditioning because the terminals at the binary switch had burned.
View repair details
Fassi
A main pressure hose burst during a lift and stopped the crane mid-job.
View repair details
HIAB M8
A maintenance inspection revealed severe lift cylinder leaks and the unit was taken out of service.
View repair details
Toyota 8FGCU30
The forklift overheated and smelled of coolant even after a previous pump and thermostat replacement.
View repair details
Yale ERC050
Both tilt cylinders leaked as their seals deteriorated.
View repair details
Freightliner 114SD
The truck would not start and its modules did not receive a neutral signal.
View repair details
Mack CH600
Heat and A/C cut in and out when the dash cluster moved.
View repair details
Crane
The crane would not start when the transport truck arrived.
View repair details
Genie GTH-844
The disabled telehandler blocked emergency exit doors at a hospital.
View repair details
Ford F-350 Super Duty
The 2020 truck lost braking after its pads wore to metal and damaged the rotors and calipers.
View repair details
Crown RMD6025-32
The load wheels were chipping and the customer requested replacements.
View repair details
Freightliner Cascadia P4
The truck would not start. The voltage and stalk switch faults persisted despite good wiring and switch tests.
View repair details
Ram 2500 ST
A leaking pan, filters and prior installation issues were corrected.
View repair details